无缝和焊接三通自动设计计算
Contract No.:SHCL-08PKLSS-JD-2016-01
caculation sheet
26.7
606
584
432
0
0.7
57.78
101.954
75.4178
324
216
126
105
576
426
105
216
53
******有限公司
co., LTD
计算书
Table No.:HR-PKLSSGS-JSS-01
热压三通 tee 第 1 页 共 2 页
执行标准 According to the standard：ASME B31.1
Drawing No.：HR-PKLSSGS-DWG-01
设计条件 design parameter 简图 diagram
材料
Material
采用规范
pipe code
计算压力P /MPa
Design pressure /MPa
设计温度T /℃
Design temperature /℃
连接管道主管外径Dh
Outside diameter of pipe(run)
连接管道支管外径Db
Outside diameter of pipe(branch
pipe)
附加厚度A
Corrosion allowance /mm
系数 y
Values of y
设计温度下的许用应力SE /MPa
Allowable stress in design temp.SE
主管最小壁厚Tmh
The minimum wall thickness run
支管最小壁厚Tmb
The minimum wall thickness branch
pipe
厚度设计计算 design caculation of thickness
经腐蚀的主管内径dr /mm
Corroded internal diameter of run
经腐蚀的支管内径 db /mm
Corroded internal diameter of branch pipe
不包括腐蚀余量的三通主管实际壁厚 Th/mm
Actual thickness of run wall,
不包括腐蚀余量的三通支管实际壁厚 Tb /mm
Actual thickness of branch wall,
三通主管外径 D /mm
Outside diameter of run D
三通支管外径 d /mm
outside diameter of branch pipe d
在离主管外表面上高度ro处挤压翻边出口经腐蚀的厚度 T0
Corroded finished thickness of extruded outlet measured at a height equal to
ro above the outside surface of the run T0
有效补强范围的半宽度（等于dc) r1/mm
Half width of reinforcement zone (equal to d c ) r1
在包含主管轴线和支管轴线的平面内挤压翻边出口外部轮廓线的曲率半径 r0/mm
Aadius of curvature of external contoured portion of outlet measured in the
plane containing the axes of the run and branch.
Contract No.:SHCL-08PKLSS-JD-2016-01
caculation sheet
******有限公司
co., LTD
计算书
Table No.:HR-PKLSSGS-JSS-01
热压三通 tee 第 1 页 共 2 页
执行标准 According to the standard：ASME B31.1
Drawing No.：HR-PKLSSGS-DWG-01
1
148
A 7 = K (t mh A) d −22022.00
A 1 = d c (t n t mh )−5194.00
A 2= 2L 8 (t b t mb )−8759.07
A 4 = 2r o [T o (t b A)]− − 0.00
A 1 + A 2 + A 4 13953.07
For d/D greater than 0.60,K= 1.00
For d/D greater than 0.15 and not exceeding 0.60,K = 0.6 +2 3(d/D)⁄
For d/D equal to or less than 0.15,K = 0.70
有效补强范围的高度 L8
Altitude of reinforcement zone L8
所需的补强面积 A7
Required Area A7
有效补强面积 A1
Area A 1
有效补强面积 A2
Area A 2
有效补强面积 A4
Area A 4
有效补强面积
Reinforcement Area
结论
conclusion A 1 + A 2 + A 4＞A 7 不合格
unqualified
标签： #设计
摘要：
展开>>
收起<<
ContractNo.:SHCL-08PKLSS-JD-2016-01caculationsheet26.760658443200.757.78101.95475.417832421612610557642610521653******有限公司co.,LTD计算书TableNo.:HR-PKLSSGS-JSS-01热压三通tee第1页共2页执行标准Accordingtothestandard：ASMEB31.1DrawingNo.：HR-PKLSSGS-DWG-01设计条件designparameter简图diagram材料Material采用规范pipecode计算压力P/MPaDesign...
作者：闻远设计
分类：课程设计课件资料
价格：5光币
属性：6 页
大小：250.71KB
格式：XLSX
时间：2025-02-27
